If the automatic feeding mixer is ordinary and does not pay attention to cleaning, it is very easy to stick to the tank. The following small make-up for you to analyze what is the reason.

　　在每次卸料之后，用罐车自己带水枪对罐口、叶片、进料口、罐体以及犄角旮旯停止冲洗，防止混凝土熔化之后越积越多，不好清算。天天的输送义务停止之后，在罐内加入1立方米以上的净水，倏地的旋转罐体停止荡涤。有条件的公司，还能够在罐内加入石子，效果会更好。在运营时随时冲洗，收车之后彻底荡涤罐车。

　　After each unloading, stop washing the tank mouth, blade, feeding port, tank body and corner with water gun to prevent the concrete from accumulating after melting, which is not easy to settle. After the daily delivery obligation stops, add more than 1 cubic meter of purified water into the tank, and then the rotating tank stops cleaning. Qualified companies can also add stones in the tank, and the effect will be better. Wash at any time during operation and thoroughly clean the tank car after collection.

　　自动上料搅拌车加水流程：控制气压，固禁接头。罐体气压在出厂的时光已经设定好了，无需自己调节，假如出现特别情形须要自己调节，提议气压控制在3.5mpa阁下。

　　Water adding process of automatic feeding mixer: control the air pressure and forbid the joint. The tank air pressure has been set before leaving the factory, so it is not necessary to adjust it by yourself. In case of special circumstances, it is suggested that the air pressure should be controlled at 3.5Mpa.
           

　　由于原料差别，每一盘的混凝土品德都有些差别，装好混凝土时，一定要检查它的坍落度以及合易度，小心混凝土的提前熔化跟混凝土分层沉淀，以免运到现场后混凝土又不克不及投入运用，糟蹋人力物力时光。留心输送的距离，可能造成混凝土品德改变，这个距离尽量控制在直径30范围以内。

　　Due to the difference of raw materials, the concrete quality of each plate is different. When installing the concrete, it is necessary to check its slump and workability. Be careful of the concrete melting in advance and the layered precipitation of concrete, so as to avoid that the concrete can not be put into use after being transported to the site, which will waste the manpower and material resources. Pay attention to the distance of conveying, which may cause the change of concrete quality. The distance should be controlled within the range of 30km in diameter.

　　搅拌车出车之前计划好道路以及车辆通行情形，只管增加车辆在路上的时光。碰到人为或许不可抵抗的要素招致无法卸料时，随时检查罐内情形，一旦发现有混凝土开端熔化，应立即卸料，以免造成全部罐体的报废。

　　Plan the road and the traffic situation before the mixer starts, just increase the time of the vehicle on the road. When it is impossible to unload due to man-made or irresistible factors, check the situation in the tank at any time. Once it is found that the concrete begins to melt, the material should be unloaded immediately, so as to avoid the scrapping of all the tanks.

　　以上就是有关自动上料搅拌车加重的原因及方法，想要了解更多请关注我们的网站http://www.jfhntjbc.com。

　　The above is about the reasons and solutions of automatic feeding mixer truck. For more information, please pay attention to our website http://www.jfhntjbc.com 。