1、搅拌一体车主机的润滑检查，在搅拌一体车主机运行时，可观察润滑脂泵刮油器是否在正常运转的刮油。

　　1. Check the lubrication of the main engine of the mixer. When the main engine of the mixer is running, you can observe whether the grease pump scraper is in normal operation.

　　2、观察润滑脂泵压力表的压力值，正常情况下工作压力为10bar---60bar，如压力低于10bar，则可能为润滑脂泵泵芯磨损或泵芯堵

　　2. Observe the pressure value of the grease pump pressure gauge. Under normal conditions, the working pressure is 10bar-60bar. If the pressure is lower than 10bar, the pump core of the grease pump may be worn or blocked

　　塞，如压力高于60bar，则可能为分配阀堵塞或后面地管路堵塞。

　　Plug, if the pressure is higher than 60 bar, the distribution valve may be blocked or the pipeline behind it may be blocked.

　　３、在每个轴头有一个备用黄油嘴，用手指甲压下黄油嘴的顶珠，如有润滑脂溢出，则证明轴头润滑到位，反之则证明轴头润滑不到位

　　3. There is a spare grease fitting on each shaft head. Press down the top bead of the grease fitting with fingernail. If grease overflows, it proves that the shaft head is lubricated in place; otherwise, it proves that the shaft head is not lubricated  In place

　　4.风压压力在搅拌一体车主机运行的情况下正常值应为0.2----0.5bar，在搅拌拖泵一体机主机停止的情况下应为１---1,5bar，如超过或低于此两值，应

　　4. The normal value of air pressure should be 0.2-0.5bar when the main engine of the mixing machine is running, and it should be 1-1,5bar when the main engine of the mixing and towing pump is stopped. If it is higher or lower than these two values, it should be

　　调整减压阀压力。

　　Adjust the pressure reducing valve.
              

　　5、搅拌一体车主机强电接线盒，保持密封，严禁用水冲洗。

　　5. The strong current junction box of the main engine of the mixing machine shall be sealed, and it is forbidden to wash it with water.

　　6、在自动生产状态下，搅拌一体车主机卸料门手动手柄应处于收回位置，且球阀应处于中位，两个手自动转换螺堵应全部拧紧，避免手油

　　6. In the automatic production state, the manual handle of the discharge door of the main engine of the mixer should be in the retracted position, and the ball valve should be in the middle position. The two manual automatic transfer screw plugs should be tightened to avoid hand oil

　　泵过早损坏。

　　The pump failed prematurely.

　　7、搅拌一体车主机卸料门位置检测开关与感应锥的间隙。

　　7. The clearance between the position detection switch of discharge door and the induction cone of the main machine of the mixer.

　　8、搅拌一体车主机减速箱应注意到加油和换油，检查齿轮油是否充足，可以观察其示油器的油位，在搅拌一体车主机停机状态下，油位应在中位

　　8. Attention should be paid to oil filling and oil change for the reducer of the main engine of the mixer. Check whether the gear oil is sufficient. The oil level of the oil indicator can be observed. When the main engine of the mixer is stopped, the oil level should be in the middle

　　以上，即红线以上。（齿轮油的牌号为美孚６２９＃或壳牌１５０＃，用油量为１６公升）另应经常检查减速机运行是否平稳是否有噪音或异响。

　　Above, that is, above the red line. (the brand of gear oil is Mobil 629 or shell 150, and the oil consumption is 16 liters). In addition, it is necessary to check whether the reducer runs smoothly and whether there is noise or abnormal noise.