When we use the automatic loading mixer in our actual operation, sometimes it will lead to blockage due to some reasons. To a certain extent, it can directly affect the structural efficiency of the mixer, and then let the editor teach you some ways to prevent blocking it.

1.卸载时刻参数是不合理的

1. The parameter of unloading time is unreasonable

因为自动上料搅拌车无法在料仓中安装料位机，因此该职业基本上具有时刻控制。如何设置时刻参数，加载和卸载时刻设置实际上十分简单。使用时，首要设置一个小时刻，然后根据每个吸入方位渐渐添加，当物料水平达到吸进口时刻，然后减去一秒是合理的时刻。放电时刻是为了保证资料再次放电。这有两个长处：首要，资料水平太高，并且对过滤元件的损坏特别大。因为这个原因，咱们的一些客户能够使用一个过滤器两年半。第二，每次清洁物料时，切断阀在关闭时不会关闭阀门，并且阀门频频操作的密封阀未切换五次或六次是特别有害。

Because the automatic feeding mixer can not be installed in the bin level machine, so the occupation basically has time control. How to set time parameters, loading and unloading time setting is actually very simple. When using, first set a small time, and then add gradually according to each suction direction. When the material level reaches the suction inlet time, then subtract one second is a reasonable time. The discharge time is to ensure the data discharge again. This has two advantages: first of all, the data level is too high, and the damage to the filter elements is particularly large. For this reason, some of our customers can use a filter for two and a half years. Second, when cleaning materials, the shut-off valve will not close when it is closed, and it is particularly harmful that the frequently operated sealing valve is not switched five or six times.
                

2.自动上料搅拌车进料口的进料量是否合理？

2. Is the feeding rate of the automatic feeding mixer reasonable?

咱们的许多项目都使用手动枪来吸取资料。为了便于将资料枪直接插入资料筒或吨袋中，资料枪的吸进口被紧密的资料压缩，强大的负压将完整的资料拉走。装载机十分具有损坏性，能够轻松堵塞管道。正确的方法是资料在吸进口和空气中构成必定的气液混合比，并在气流的推动下均匀地流入进料器。假如资料积压时刻太长，可能会十分困难。此时，枪上需求一个振荡器来损坏凝聚的资料。

Many of our projects use manual guns to get information. In order to insert the data gun directly into the data cylinder or the ton bag, the suction inlet of the data gun is compressed tightly and the complete data is pulled away by the strong negative pressure. Loaders are very destructive and can easily plug pipes. The correct method is to form a certain gas-liquid mixing ratio in the suction inlet and air, and flow into the feeder evenly under the push of air flow. If the backlog is too long, it may be very difficult. At this point, the gun needs an oscillator to damage the condensed data.

在自动上料搅拌车的实际操作中，不可防止地会发生某些故障。堵塞材料更严重。因此，我希望在了解上述自动上料搅拌车的回避方法后，能够正确合理地操作设备。

In the actual operation of the automatic feeding mixer, some faults can not be prevented. The blocking material is more serious. Therefore, I hope that after understanding the above avoidance methods of automatic feeding mixer, I can operate the equipment correctly and reasonably.