保养对搅拌车的重要性都知道，那么怎样保养才能确保我们的设备长久使用且不出问题呢？搅拌一体车厂家为您解说。

We all know the importance of maintenance to the mixer truck, so how can we ensure that our equipment can be used for a long time without problems? The mixer manufacturer will explain to you.

1、检查车辆发动机机油、柴油、转向油、离合器油、制动油液及发动机冷却液等的加注情况，确保车辆的正常使用，并及时更换和清理机油滤芯、柴油滤芯、空气滤芯。

1. Check the filling of engine oil, diesel, steering oil, clutch oil, brake oil and engine coolant of the vehicle to ensure the normal use of the vehicle, and timely replace and clean the engine oil filter element, diesel filter element and air filter element.

2、检查转向系统、离合器、制动系统工作是否正常。检查照明灯、报警器、转向指示灯、刹车灯、雨刮器等动作是否正常,均应清洁。检查轮胎气压是否正常,不应有破裂和损伤，轮胎螺母不得有松动。

2. Check whether the steering system, clutch and braking system work normally. Check whether the action of lights, alarms, direction indicators, brake lights, wipers, etc. is normal and should be cleaned. Check whether the tire pressure is normal, there should be no cracking and damage, and the tire nut should not be loose.

3、检查完毕启动车辆进行预热，检查机油压力、发动机水温是否正常，底盘气路有无漏气情况。

3. After inspection, start the vehicle for preheating, check whether the oil pressure and engine water temperature are normal, and whether the chassis air circuit has air leakage.

4、检查带有尿素的车辆，发动机熄火少30S以内不要关闭车辆总电源，此时系统会将管道残余的尿素溶液排除，以避免结晶堵塞喷嘴。

4. Check the vehicle with urea. Do not turn off the main power supply of the vehicle within at least 30s after the engine is shut down. At this time, the system will discharge the residual urea solution in the pipeline to avoid crystallization blocking the nozzle.

5、检查液压泵、马达、减速机是否有漏油现象，检查液压油、减速机齿轮油是否充足，有无变质，液压油滤芯是否满足使用要求，液压油散热器能否正常运行。6、检查主、副车架连接螺栓是否松动、脱落；检查副车架及底盘大梁是否有开裂现象。

5. Check whether the hydraulic pump, motor and reducer have oil leakage, whether the hydraulic oil and reducer gear oil are sufficient and deteriorated, whether the hydraulic oil filter element meets the use requirements, and whether the hydraulic oil radiator can operate normally. 6. Check whether the connecting bolts of the main and sub frames are loose and fall off; Check whether the subframe and chassis girder are cracked.

7、检查滚道及托轮表面是否有异物，并及时；转动搅拌筒，查看是否有抖动、异响等；查看托轮紧固螺栓是否松动，托轮是否移位；滚道、托轮表面、托轮内部涂抹润滑脂。

7. Check whether there are foreign matters on the surface of the raceway and supporting wheel, and remove them in time; Rotate the mixing drum to check whether there is shaking, abnormal noise, etc; Check whether the fastening bolts of the supporting wheel are loose and whether the supporting wheel is displaced; Apply grease on the surface of the raceway, the supporting wheel and the inside of the supporting wheel.

8、检查进料斗、溜槽处是否有结料并；检查溜槽伸缩支撑旋转时是否伸缩正常，并往伸缩支撑及支撑摇杆处加注润滑脂。

8. Check whether there is material deposition at the feed hopper and chute and remove it; Check whether the expansion and contraction of the chute telescopic support is normal when rotating, and fill the telescopic support and the support rocker with grease.

9、检查传动轴连接螺栓是否松动，传动轴花键及十字轴处加注润滑脂。

9. Check whether the connecting bolts of the transmission shaft are loose, and add grease to the splines and cross shafts of the transmission shaft.

10、检查转动操纵手柄操纵是否卡滞，操纵各油嘴处加注润滑脂。

10. Check whether the operation of turning the joystick is stuck, and fill grease at each oil nozzle.

以上为搅拌车开工前的检查保养的注意事项，希望能对大家能有所帮助，更多相关的事项就来我们网站http://www.jfhntjbc.com咨询看看吧。

The above are the precautions for the inspection and maintenance of the mixer truck before construction. I hope it can be helpful to you. For more relevant matters, please come to our website http://www.jfhntjbc.com Consult and have a look.