It is very dangerous for the mixer engine to overheat. If you are lucky, the engine may be destroyed. This is to take emergency measures. Do not need to drive urgently. How to follow the manufacturer of the automatic concrete loading mixer truck:

在行驶中出现过热现象应该尽快地降低车速，把汽车驶到树荫下，或驶到相比照较凉爽的处所，把汽车停下来。打发动机罩盖，让发动机怠速运转，等待发动机温度逐步恢复一般。正在发动机水温恢复一般之后，将发动机熄火。然后再等待一段时间，曲到发动机的水温充实地下降了之后，再查抄发动机的冷却水量。那时发动机的冷却水量大都严峻不敷。按照划定量把冷却水补足之后，再查抄一下冷却系统，确认没有毛病之后，能够起动发动机，继续行驶。

In case of overheating during driving, reduce the speed as soon as possible, drive the car into the shade of trees or drive to a cooler place, and stop the car. Open the engine cover, let the engine idle, wait for the engine temperature to gradually return to normal. After the engine water temperature returns to normal, turn off the engine. Then wait for a period of time until the engine's water temperature plummets, and then check the engine's cooling water. At that time, the cooling water of the engine was mostly insufficient. After making up the cooling water according to the specified amount, check the cooling system again. After confirming that there is no problem, the engine can be started and continue to drive.
             

为了更好的使用混凝土自动上料搅拌车，日常驱动装置的维护保养工作不能少。

In order to better use the concrete automatic loading mixer, the daily drive device maintenance work can not be less.

a.保证液压油清洁。混凝土搅拌运输车工作环境恶劣，一定要防止污水泥沙进入液压系统。液压油要按使用手册要求定期更换。一旦检查时发现液压油中混入水或泥沙，就要立即停机清洗液压系统、更换液压油。

a. Keep the hydraulic oil clean. The working environment of concrete mixer truck is bad, so it is necessary to prevent dirty cement sand from entering the hydraulic system. The hydraulic oil should be replaced regularly according to the requirements of the manual. Once it is found that the hydraulic oil is mixed with water or sediment, it is necessary to stop the machine immediately to clean the hydraulic system and replace the hydraulic oil.

b.保证液压油冷却装置有效。要定时清理液压油散热器，避免散热器被水泥堵塞，检查散热器电动风扇运转是否正常，防止液压油温度超标。液压部分只要保证液压油清洁，一般故障不多;但生产厂家不同，使用寿命则不一样。

b. Ensure that the hydraulic oil cooling device is effective. The hydraulic oil radiator should be cleaned regularly to prevent the radiator from being blocked by cement, and check whether the electric fan of radiator operates normally to prevent the temperature of hydraulic oil exceeding the standard. As long as the hydraulic oil is clean, there are not many faults in the hydraulic part, but the service life varies with the manufacturer.

c.万向转动部分是故障多发部位，应按时加注润滑脂，并经常检查磨损情况，及时修理更换。车队应有备用的万向轴总成，以保证一旦发生故障能在几十分钟内恢复工作。

c. The universal rotating part is a fault prone part, so grease should be added on time, and the wear condition should be checked frequently, and the repair and replacement should be carried out in time. The team should have spare cardan shaft assembly to ensure that it can resume work in dozens of minutes in case of failure.

以上就是关于混凝土自动上料搅拌车如何处理温度过高现象的介绍，希望对大家有所帮助，如您想要了解更多资讯内容请点击我们的网站：http://www.jfhntjbc.com。

The above is about how to deal with the phenomenon of excessive temperature in the automatic concrete feeding mixer. I hope it can help you. If you want to know more about it, please click our website: http://www.jfhntjbc.com 。